With each episode, they seem incomplete stories. In general, the controls are clunky and it’s a bit stressful to play. I tried typing “go to kitchen”, “go outside”, but it actually expected “go to hallway”, then from the hallway I could move to the kitchen. I tried “look at room”, “look at people” without success, then I assumed we needed to leave the room. So for example, it tells you that you are in a room of people you don’t recognise, but doesn’t give you any more info than that. Often, the objects you need to type aren’t displayed on screen. When you play the text adventure, certain commands seem to work in some areas, but not others. It doesn’t do a great job of explaining what you need to do. However, I think this highlights the main problem with the game. At this point, I realised there were controls to zoom and focus the text to see the microfiche, so maybe it wasn’t hard to see the text in episode 3 afterall. The fourth episode revisits mechanics from the previous three. I found it difficult to see the text, and some of the instructions seemed a bit cryptic, so I looked up what you needed to do on a walkthrough. Then you need to check microfiche for the next codes to enter. In the third episode, you are adjusting a radio to pick up a code to enter in the computer. You have a computer with the instructions, so need to check them to work out which machine to turn on and adjust. In the second episode, you are performing lab experiments by switching on machinery and turning dials. At first, you play a normal version of the game, but then replay a creepier version. You type in commands to navigate a house like “open door”, “go to hallway”. In the first episode, you are playing a text-based adventure game on the Spectrum computer. I won’t go into detail about the fourth episode because it’s basically a story based game, and if you explain the plot then it is a spoiler. There are 4 episodes in the game, and the first three seem unrelated, but all is explained in the fourth. Now you are back in the text adventure mode you already know from the first chapter of the game.I haven’t even seen Stranger Things, but the theme music and logo of Stories Untold instantly made me think of Stranger Things. Struggling with episode 3 PURESSENCE 1,811,267 Posted on 03 November 20 at 12:29 I'm on the second set of 3 inputs, where the final one needs you to replace XYZ with three numbers from the. > You find the room names above the doors! > Move your cursor onto the orb right in front of you, click and hold, the light will turn red and trigger a cutscene > Use the arrow keys to enter the following first three symbols, then just go to the last and use the right arrow key three times till it triggers the cutscene Click and hold, the light will turn blue and trigger a cutscene > Move your cursor onto the orb till the light starts flickering red. On the file cabinet in the corner you find the first cassete. > Go back to the hallway and around the corner. At the wall next to the door to Ward 4 is a dispenser for hand sanitizer. On the chair in the far left corner is the second cassette. > Go back to the hallway and enter the Office. On the file cabinets you find the third cassette. > Go back to the hallway and enter the Pre-Surgery room. On a side table you find the last cassette. Click on the round silver button, hold and move your mouse upwards till it reads 100J Go around the corner and through the door from which the light shines in > Go to the end of the hallway and exit through the double door. Click on the round button, hold and move your mouse upwards till it's on full charge 5 Tiny Room Stories Walkthrough Chapter 5 Mountain 6 Tiny Room Stories Walkthrough Chapter 6 Cave 7 Tiny Room Stories Walkthrough Chapter 7. > Click on the round silver button on th Signal Generator, hold and move your mouse upwards till it reads 200J Stories untold walkthrough part 3 full#ħ.1 Chapter 7 Full 7.2 Chapter 7 Forest Part 1 7.3 Chapter 7 Gas Station Part 2 7.4 Chapter 7 52 Cardon Street Part 3 8 Tiny Room Stories Walkthrough Chapter 8 Next Lab 9. > Put the TV Unit in the RGB setting by clicking the silver slider under the screen twice > Put the TV Unit in the xray setting by clicking the silver slider under the screen twice > Click on the small black pentagonal switch in the middle of the CC86 Xray to load it > Click on the round silver button on th Signal Generator, hold and move your mouse upwards till it reads 360J > The Sync Master will start blinking green.
0 Comments
Leave a Reply. |